Yeah, I hear you on that. But my view is, that’s how much it cost. Cancelling it won’t make it cheaper in the future. Sometimes we just need to bite the bullet and pay for what we need.

It’s more like an issue with initial quotes than the actual cost of the thing. The problem is, the public sees a big cost and screams “they’re wasting our money!”, but that’s not really it at all. The government is trying to invest in needed infrastructure that benefits all of us in the future. Literally their job.

Mate, the infrastructure is reaching end of life anyway and needs replacing.

The benefit of doing it all at once is they were enlarging both terminals to allow better offloading of freight. Pay more now to spend less later.

The dumbest thing about changing teacher only days, is they are not counted in then mandatory number of days a school is open for. All this change will do is make them close earlier, so the kids will still be off school and parents will still need to make arrangements.

It’s fucking stupid.

Cheers mate. Neat stuff!

I wonder how much force a sail of that size is expected to produce?

I agree with you, and I think it’s interesting to look at why there is a short term uptick in youth crime.

Something something cost of living crisis something something

It’s all good mate! Thanks for the suggestion. When I first started printing I had that exact issue.

Hey mate, I keep my filament in a dry cabinet at 5ish% humidity, and I’ve had the same results with two different filaments in there. I even chucked my filament in a food dehydrator at 40C for 12h with no effect. I’m pretty sure the filament is dry!

I love these! Thanks for sharing!

After sleeping on it, I remembered that my new heatbreak doesn’t feed the bowden all the way to the end of the nozzle like the stock one does, so I’m pretty sure I have it seated correctly. I’ll check it though, many thanks for the info! :)

I know esun is quite popular, but I never tried it.

I’ve generally had the best results with it. Ironically, before the upgrades I had almost no stringing.

I’m using a 0.4mm nozzle. I probably should have mentioned in the OP that I didn’t have problems before, but the upgrades have happened in addition to moving to Orcaslicer.

Now I’m worried if I’ve got my Bowden tube seated in the hotend correctly…

Thanks for the reply mate!

I didn’t think to mess with z-hop - I’ll give that a go, and I’ll do some testing to make sure the Bowden is seated correctly and the wipe on retract is actually happening - thanks!

The print in the image is a ‘torture test’, and just something I had on hand to illustrate the issue. I’m actually not fussed if there is still some stringing at the top, but other detailed prints were getting it pretty bad, including retraction towers.

Thanks. I’ll try that.

Hmm yes, good points. I’ll have another go with the previous filament.

To be fair, I need to replace the extruder and get a high flow nozzle anyway, which I think will make more difference to the flow rate than running hot.

What temperature are you printing at? When I was using Marlin I ran mine at about 200, and could probably have gone even lower. I also tuned linear advance which made a big difference.

I have found that some esun spools weren’t particularly dry when I got them. They sit in my dehumidifier which sits at about 20%, so they get dry eventually.

You can try coasting as well I think.

Yeah lower temps work, but I’m really trying to max out my flow rate so I want to run it as high as possible. Pressure advance really helps reduce ooze, and quality filament is obviously a must.

That site doesn’t load for me. I have just been using a retraction tower and running the tuning function from the command line.

In the end it was crap quality filament.

I keep my spools in a dehumidifier which I actually think is too dry. Some of the filament was brittle for the first 6" or so.

Yeah it was rubbish filament. Switched it out for some esun PLA+ and got much better results. I’ve updated my post, but final settings are:

Pressure Advance - 0.4 Retraction - 3.5mm Retraction speed - 35mm/s

Very happy with the results!

Thanks for your reply, I will give that a go.

After posting I thought to try a different brand of filament. It’s currently printing, so we’ll see how it goes.

I for one welcome our new terrible carnivorous crab overlords